Features:

1》The fuselage adopts the national standard 6mm thick Q355B manganese plate (the other ones use non-standard ordinary carbon plates, which are 0.15mm thinner than the national standard plate), the chassis uses 4mm thick Q355B manganese plate, ultra-high wear resistance, the fuselage structure is strengthened by the anti-roll frame, the fuselage uses a semi-wrapped structure, which solves the engine heat dissipation to the greatest extent, adopts a low-lying design, the center of gravity is more stable, and has better passability in narrow areas, and the strong structure ensures that the fuselage is not deformed

2》Use electro-hydraulic push rod to control the lifting header (with -25°C hydraulic oil) strong pulling force, the output of the cutter shaft becomes more stable after 3000 rotation balance processing, each set of blades and the blade directly leave a gap, the inside plus nylon gasket to isolate the blade, the fixed blade pin is made of 8.8 grade high hardness steel, will not wear, the pin is fixed with 8.8 grade bolts and anti-dislodging nuts, and both ends of the cutter shaft are fixed with maintenance-free high-speed bearing housings to make the cutter shaft blade super silky and durable

3》Equipped with high-quality American imported Briggs & Stratton commercial series engines:
1. We provide customers with free upgrade to top configuration, equipped with 45° large angle operation attachment (can operate stably under 45° tilt), remote control electric start system, high efficiency power generation system, transportation protection system, low noise muffler and battery-free manual start system.

2. The engine air intake adopts a double-layer nano cyclone air filter, equipped with a full cyclone air duct patented design, to prevent the finest dust from entering the engine.

3. Adopt CDI variable ignition timing, so that the engine can be easily started in any weather condition, without the need to control the choke.

4. The engine is started with a separate starting battery, and the battery life can reach 5 years, which reduces the operation of frequent battery replacement when the battery is not durable

5. Use a tilting anti-leakage fuel tank cap to ensure that the tilt angle is 45°, and the fuel will not leak out

4》Use extended tracks The ground contact distance is 1.2 meters 150mm wide with 5 cast steel double-layer wheels, never deformed and never fall off the tracks

5》Add control compartment to add heat dissipation system and add protective fuse

6》Servo motor, reducer：
1.The walking motor uses two 48V, 1200W motors, equipped with standard length output shafts, and original 2500 PPR servo magnetic encoder motors. It features multi-core differential signals: UVW commutation, ABZ incremental, SPI debugging, with shielding for anti-interference. It supports full closed-loop control, capable of position loop, speed loop, and current loop three-loop control. The magnetic encoder is vibration-resistant and oil-resistant, suitable for complex industrial/outdoor scenarios, including inspection reports. In combination with our independently developed controller, it is long-lasting, durable, and will not overheat.

2. The servo motor integrates RV063 worm gear and worm reducer. The design includes a self-locking mechanism that prevents motor movement in the event of a power outage. The high friction between the worm and the worm gear ensures that the motor remains stationary, enhancing safety by preventing accidental sliding or rolling on slopes

3. The output shaft of the reducer uses 40cr quenched and tempered shaft After output, a reinforced support flange is added, the outermost part is used with cast iron bearing housing, the internal is made of Chinese maintenance-free bearing, and the track drive wheel is integrated with laser-cut manganese steel to ensure that the output shaft will not break permanently

7》Add overhead headlights, add engine timer, add forest fire prevention electric fire extinguishing system, add slope meter, add dual battery engine self-charging system, and optional 500-meter long-distance control remote control with voltage return

8》The whole machine uses brass metal waterproof plugs, uses surface treatment pulleys, and all axial parts of this machine are all rust-proof

9》 Both the starter relay and the long-duration relay use strong magnetic arc-extinguishing silver contact relays, which provide high-quality and stable output but are expensive.

10》 The controller wires, generator output wires, and engine start wires all use 10 square millimeter pure copper wires for efficient current transmission.

11》 The travel motor uses a high-efficiency graphene battery.

12)》Dealers can provide a motor debugging app.

Specification:
Model: VDTK-1000
Cutting Width: 1000mm
Walking Speed: 0-4km/h
Working Degree: 0-45°
Adjustable Cutting Height: 10~165mm
Min Ground Clearance: 45mm
Remote Control Range: 200m/500m

Engine：
Brand: Briggs & Stratton
Fuel Type: Gasoline
Engine Type: Single-cylinder, air-cooled, four-stroke, overhead valve
Power / Emission: 14HP / 408cc
Start Method: Electric start
Lubrication System: Splash + pressure
Emission Standard: Euro5/EPA
Fuel Tank: 6.1L
Engine Oil Capacity: 0.94L
Working Time: 2h (full fuel)

Walking Motor：
Motor Type: Servo control
Voltage / Power: 48V / 1200W
Dynamo: 56V 4000W
Battery: 48V 20.3Ah
Machine Size: 2000*1200*660mm
Machine Weight: 490kg
Package Size: 2060*1260*810mm
Gross Weight: 570kg